WRAP SEAL ULTRA QUICK REPAIR KIT FOR ACTIVE PIPE LEAKS

WRAP SEAL ULTRA QUICK REPAIR KIT FOR ACTIVE PIPE LEAKS

FEATURES:

• Repairs under active leak up to 150 psi (11 kg/cm2) pressure
• No shutdown required
• Works on any metal or non-metal pipes
• Applicable to pipes up to 18″ (457 mm) diameter
• Repairs leak in 15 minutes
• Withstand pressure up to 500 psi (35 kg/cm2)
• Withstand temperature up to 200 °C (392 °F)
• Safe for drinking water and resistant to most chemicals
• Ideal for pipeline reinforcement

APPLICABLE MATERIAL:

• Steel
• Copper
• Aluminium
• Galvanized steel
• PVC
• CPVC
• Stainless steel
• Polyethylene
• Polypropylene
• Cast-iron
• Concrete
• FRP/GRE

CHEMICAL RESISTANCE:

• Oil
• Water (drinking water, wastewater, steam)
• Solvents (acetone, toluene, MEK, ethyl alcohol)
• Mild acids (hydrochloric acid, sulfuric acid) and alkalis
• Chemical (ethylene glycol, xylenes, ammonia)
• Hydrocarbons
• Bases
• Slurries
• Fuels (petroleum, diesels, gasoline)
• Gases (LNG, LPG)
• Organic salts

WORKING TIME (FIBERGLASS TAPE):

•  1 minute at 30 °C (86 °F)

CURING TIME:

• 30 minutes at 30 °C (86 °F)
• Heat may be applied to decrease curing time
• Unopened foil pouch may be immerse in cold water prior to repair to add working and curing time.

APPLICATION:

• Pipe repairs
• active pipe leaks
• sealing joints
• hazardous material spill control
• reinforce thinning walls
• Repairs in hard to reach areas
• Underwater repairs

OPERATING TEMPERATURE:

•  -50 °C (-58 °F) to 200 °C (392 °F)

OPERATING PRESSURE:

• Recommended for pressure up to 500 psi (35 kg/cm2)
• (Result vary depending on pipe size, type of pipe, hole size, pipe content and method of application)

APPLICABLE INDUSTRIES:

• Building & amp; Facilities
• Electronics
• Industrial Processing
• Irrigation
• Oil & amp; Gas
• Chemical
• Manufacturing Plants
• Marine
• Military
• Offshore
• Food Processing
• Petrochemical
• Pharmaceutical
• Power Generation
• Pulp & amp; Paper
• Wastewater
• Water Distribution

TECHNICAL DATA:

1. Tensile strength: 3920 psi (276 kg/cm2)
2. Bond strength: 230 psi (16 kg/cm2)
3. Tensile elongation: 1.2 % ± 0.7 %
4. Compression strength: 13750 ± 530 psi (967 ± 37 kg/cm2)
5. Yield strength: 2260 psi (159 kg/cm2)
6. Cured hardness: 82 Shore D
7. Dielectric strength: 400 Volts/mil

Pipe size	Number of rolls / size required
	50 psi (4 kg/cm2) 10 plys	150 psi (11 kg/cm2) 15 plys	400 psi (28 kg/cm2) 20 plys
½” (15mm)	1 A	1 A	1 A
¾” (20mm)	1 A	1 A	1 A
1″ (25mm)	1 A	1 A	2 A
1¼” (32mm)	1 A	2 A	3 A
1½” (40mm)	2 A	2 A	1 B
2″ (50mm)	1 B	1 B	1 B
2½” (65mm)	1 B	1 B	2 C
3″ (80mm)	1 B	2 C	2 C
4″ (100mm)	1 B	2 C	3 C
5″ (125mm)	2 C	2 C	3 C
6″ (150mm)	2 C	2 C	4 C
8″ (200mm)	2 C	3 C	5 C
10″ (250mm)	3 C	4 C	6 C
12″ (300mm)	4 C	5 C	8 C
14″ (350mm)	4 C	6 C	8 C
16″ (400mm)	5 C	7 C	9 C
18″ (450mm)	5 C	8 C	9 C
> 18″ (450mm)	Contact SealXpert for recommendations

Roll size

A (2″ x 5′) (50mm x 1.2m)

A (2″ x 6′) (50mm x 1.8m)

B (2″ x 12′) (50mm x 3.6m)

B (3″ x 9′) (75mm x 2.7m)

C (4″ x 12′) (100mm x 3.6m)

WRAP SEAL ULTRA ACTIVE LEAK REPAIR PROCEDURE:

• Minimize the flow rate and reduce system pressure
• Roughen the area to be repaired
• Knead the Seal Stic
• Place the Seal Stic away from the leak location
• Start wrapping the SealXpert Ultra Sealing Tape a few distances away from the leak location
• Continue to wrap SealXpert Ultra Sealing Tape onto pipe while pushing the Seal Stic onto leak location
• Immerse Wrap Seal Fiberglass Tape into water
• Wrap the Wrap Seal Fiberglass Tape above the repair tape as tightly and evenly as possible, using the entire roll
• Discard the plastic tube at the end of the roll
• Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap until all bubbling has stopped. Repair completed with smooth and hard ivory appearance

Back to pipe repair kit PACKAGE:

A. 1 roll of Wrap Seal Fiberglass Tape

• 2″ x 6′ (50 mm x 1.8 m)
• 2″ x 12′ (50 mm x 3.6 m)
• 3″ x 9′ (75 mm x 2.7 m)
• 4″ x 12′ (100 mm x 3.6 m)

B. 1 roll of SealXpert Ultra Sealing Tape

• 1″ x 16′ (25 mm x 5 m)
• 1″ x 16′ (25 mm x 5 m)
• 1¼” x 16′ (32 mm x 5 m)
• 2″ x 16′ (50 mm x 5 m)

C. 1 unit of Seal Stic Quick Cure Epoxy
D. 1 pair of latex gloves
E. Operating instruction


Note: 
Pembelian bahan Kimia ini harus melampirkan Company Profile (CV atau PT), Perorangan tanpa Identitas perusahaan tidak akan dilayani.

#tokokimiabatam, #bahankimia, #kimiabatam, #chemicalsbatam, #cleaningchemicals, #floorcaremaintenance, #floorchemicals, #floorfinish, #alkalinecleaner, #superkleen

Related product you might see: