SEALXPERT STAINLESS STEEL PIPE CLIP

FEATURES

Makes pipe clips from 2” (50 mm) to 382” (9700 mm)
Easy to use
Versatile and fast to install
No special tool is required
Stainless steel 304 material
Free to cut to any diameters required

APPLICATION

For securing, mounting, strapping, clamping and positioning
Can be used for all conventional clamping jobs
Make any sizes from 2” (50 mm) diameter to 382” (9703 mm) diameter within seconds

APPLICABLE INDUSTRIES

Building & amp; Facilities
Electronics
Industrial Processing
Irrigation
Oil & amp; Gas
Chemical
Manufacturing Plants
Marine
Military
Offshore
Food Processing
Petrochemical
Pharmaceutical
Power Generation
Pulp & amp; Paper
Wastewater
Water Distribution

TECHNICAL DATA

Material grade	All stainless steel 304
Band length	100’ (30.5 m)
Band width	0.5” (12.7 mm)
Head	0.3” (7.9 mm) slotted hex head screw
Closure components	0.6” (14.2 mm) wide fastener & screw housing assembly

SEALXPERT STAINLESS STEEL PIPE CLIP INSTALLATION PROCEDURE
I. Determine actual band length in one of two ways:
(a) If diameter is known, refer to band length table below
(b) If diameter is not known, measure circumference with string, twine, etc. and subtract 4” (to allow for length of fastener ends) to determine actual band length.

Pipe Diameter	Length to cut on Mark	Pipe Diameter	Length to cut on Mark	Pipe Diameter	Length to cut on Mark
2” (50.8 mm)	2-1/2” (63.5 mm)	22” (558.8 mm)	65-7/8” (1673.2 mm)	60” (1524.0 mm)	184-13/16” (4694.2 mm)
3’ (76.2 mm)	5-1/16” (128.6 mm)	24” (609.6 mm)	72-1/8” (1832.0 mm)	62” (1574.8 mm)	191-1/8” (4854.6 mm)
4” (101.6 mm)	8-7/8” (225.4 mm)	26” (660.4 mm)	77-1/4” (1962.2 mm)	64” (1625.6 mm)	197-7/16” (5014.9 mm)
5” (127.0 mm)	11-7/16” (290.5 mm)	28” (711.2 mm)	83-5/8” (2124.1 mm)	66” (1676.4 mm)	203-5/8” (5172.1 mm)
6’ (152.4 mm)	15-3/16” (385.8 mm)	30” (762.0 mm)	89-7/8” (2282.8 mm)	68” (1727.2 mm)	209-15/16” (5332.4 mm)
7” (177.8 mm)	17-3/4” (450.9 mm)	32” (812.8 mm)	96-3/8” (2447.9 mm)	70” (1778.0 mm)	216-1/4” (5492.8 mm)
8” (203.2 mm)	21-1/2” (546.1 mm)	34” (863.6 mm)	102-5/8” (2606.7 mm)	72” (1828.8 mm)	222-9/16” (5653.1 mm)
9” (228.6 mm)	24-1/8” (612.8 mm)	36” (914.4 mm)	108-7/8” (2765.4 mm)	74” (1879.6 mm)	228-7/8” (5813.4 mm)
10” (254.0 mm)	27-7/8” (708.0 mm)	38” (965.2 mm)	115-1/4” (2927.4 mm)	76” (1930.4 mm)	235-13/16” (5989.6 mm)
11” (279.4 mm)	30-3/8” (771.5 mm)	40” (1016.0 mm)	121-9/16” (3087.7 mm)	78” (1981.2 mm)	241-1/2” (6134.1 mm)
12” (304.8 mm)	34-3/16” (868.4 mm)	42” (1066.8 mm)	128” (3251.2 mm)	80” (2032.0 mm)	247-13/16” (6294.4 mm)
13” (330.2 mm)	36-3/4” (933.5 mm)	44” (1117.6 mm)	134-5/16” (3411.5 mm)	82” (2082.8 mm)	254-1/8” (6454.8 mm)
14” (355.6 mm)	40-1/2” (1028.7 mm)	46” (1168.4 mm)	140-5/8” (3571.9 mm)	84” (2133.6 mm)	260-7/16” (6615.1 mm)
15” (381.0 mm)	43-1/16” (1093.8 mm)	48” (1219.2 mm)	146-15/16” (3732.2 mm)	86” (2184.4 mm)	266-5/8” (6772.3 mm)
16” (406.4 mm)	46-7/8” (1190.6 mm)	50” (1270.0 mm)	153-1/4” (3892.6 mm)	88” (2235.2 mm)	272-15/16” (6932.6 mm)
18” (457.2 mm)	53-1/8” (1349.4 mm)	54” (1371.6 mm)	165-7/8” (4213.2 mm)	92” (2336.8 mm)	285-9/16” (7253.3 mm)
19” (482.6 mm)	55-3/4” (1416.1 mm)	56” (1422.4 mm)	172-3/16” (4373.6 mm)	94” (2387.6 mm)	291-7/8” (7413.6 mm)
20” (508.0 mm)	59-1/2” (1511.3 mm)	558” (1473.2 mm)	178-1/2” (4533.9 mm)	96” (2438.4 mm)	298-3/16” (7574.0 mm)

Measure band to proper length and cut through center of nearest round hole with shears, snips, hacksaw, etc.

II. Measure band to proper length and cut through center of nearest round hole with shears, snips, hacksaw, etc.
III. Engage one screw housing end to one perforated end by turning screw three or four times
IV. Complete the clamp by diagonally inserting the ends of the engaged fastener assembly to the band through the tops of the square holes at each end of the band
V. Tighten finished clamp